At a glance
Based on the row for 96 %, 20 °C.
- Rated A, very good resistance
- PTFE, HDPE, EPDM, SS 316, SS 304, Aluminium, FEP, ECTFE/ETFE, PETG, PMP (10)
- Rated B, good resistance
- PP, PVDF, PVC Rigid, Acetal (POM), Polystyrene, Polysulfone (6)
- Rated C, limited resistance
- NBR, LDPE, Nylon (PA), Polycarbonate (4)
- Rated D, not resistant
- Viton (FPM), PVC Flexible, SAN (3)
- No data in the source
- Silicone
- Rated lower at 50 °C than at 20 °C
- HDPE (A → C), PVC Rigid (B → C), Polystyrene (B → D), Polysulfone (B → C), PMP (A → B)
Based on the row for 96 %, 20 °C.
Rating profile by material family
Effect of temperature, 20 °C to 50 °C
Substance
- CAS number
- 107-18-6
- Formula
- C3H6O
- Hazard symbols in the source
- F (flammable), T (toxic) (pre-GHS European symbols; check the current safety data sheet)
- Flammable
- yes
- Concentrations listed
- 96 %
- Name in the source (German)
- Allylalkohol
Resistance table: Allyl Alcohol, 96 %
| Material | 20 °C | 50 °C | Remark |
|---|---|---|---|
| Thermoplastics | |||
| HDPE | A | C | |
| LDPE | C | C | |
| PP | B | B | |
| PVC Rigid | B | C | |
| PVC Flexible | D | D | |
| PMP | A | B | |
| Polystyrene | B | D | |
| SAN | D | D | |
| Polycarbonate | C | C | |
| PETG | A | – | |
| Acetal (POM) | B* | – | |
| Nylon (PA) | C | – | |
| Polysulfone | B | C | |
| Fluoropolymers | |||
| PTFE | A | A | |
| FEP | A | A | |
| PVDF | B* | – | |
| ECTFE/ETFE | A | A | |
| Elastomers | |||
| EPDM | A | – | |
| Viton (FPM) | D | D | |
| NBR | C | – | |
| Metals | |||
| SS 316 | A | A | |
| SS 304 | A | A | |
| Aluminium | A | A | |
* estimated rating, given in the source without a temperature
Not rated in the source, so not in the table: Silicone
Rating scale
- A very good resistance
- B good resistance
- C limited resistance
- D not resistant
- – no data
- K no general statement possible
A rating marked * is an estimate in the source, not a test result. An estimate is given as one value without a temperature.
Frequently Asked Questions
Which materials resist Allyl Alcohol at high concentrations?
The materials with an A rating (resistant) for Allyl Alcohol at 20 °C are: PTFE, HDPE, EPDM, SS 316, SS 304, Aluminium, FEP, ECTFE/ETFE. These can generally be used in direct contact.
Which materials should be avoided with Allyl Alcohol?
Materials rated D (not resistant) for Allyl Alcohol are: Viton (FPM), PVC Flexible, SAN. These should not be used in contact with Allyl Alcohol.
Does temperature affect chemical resistance to Allyl Alcohol?
Yes. 5 of 17 tested materials show a worse rating at 50 °C than at 20 °C for Allyl Alcohol. Materials affected include: HDPE, PVC Rigid, Polystyrene, Polysulfone, PMP.
Is PTFE safe for Allyl Alcohol?
PTFE is rated A for Allyl Alcohol at 20 °C. A rating of A means resistant, B means limited resistance, C means partly resistant, and D means not resistant.
About this data
The ratings come from the chemical resistance list published by Bürkle GmbH, which compiled them from raw-material manufacturers’ data. They describe laboratory tests on the raw material at 20 °C and 50 °C.
A finished part also sees pressure, mechanical stress, welds and mixtures that a laboratory test does not. Treat the rating as a first filter and test under your own conditions before relying on it.
Chemicals with a similar resistance profile
Same 20 °C rating on the share of materials shown.