At a glance
Based on the row for 100 %, 20 °C.
- Rated A, very good resistance
- PTFE, HDPE, PP, SS 316, SS 304, Aluminium, FEP, ECTFE/ETFE, Nylon (PA), Acetal (POM) (10)
- Rated B, good resistance
- none (0)
- Rated C, limited resistance
- PVDF, EPDM, LDPE (3)
- Rated D, not resistant
- PVC Rigid, Viton (FPM), NBR, Polycarbonate, PVC Flexible, Polystyrene, Polysulfone, PETG, PMP, SAN (10)
- No data in the source
- Silicone
- Rated lower at 50 °C than at 20 °C
- HDPE (A → C), PP (A → C), LDPE (C → D), ECTFE/ETFE (A → B)
Based on the row for 100 %, 20 °C.
Rating profile by material family
Effect of temperature, 20 °C to 50 °C
Substance
- CAS number
- 141-78-6
- Formula
- C4H8O2
- Hazard symbols in the source
- F (flammable) (pre-GHS European symbols; check the current safety data sheet)
- Flammable
- yes
- Concentrations listed
- 100 %
- Name in the source (German)
- Ethylacetat
Resistance table: Ethyl Acetate, 100 %
| Material | 20 °C | 50 °C | Remark |
|---|---|---|---|
| Thermoplastics | |||
| HDPE | A | C | |
| LDPE | C | D | |
| PP | A | C | |
| PVC Rigid | D | D | |
| PVC Flexible | D | D | |
| PMP | D | D | |
| Polystyrene | D | D | |
| SAN | D | D | |
| Polycarbonate | D | D | |
| PETG | D | D | |
| Acetal (POM) | A | A | |
| Nylon (PA) | A | – | |
| Polysulfone | D | D | |
| Fluoropolymers | |||
| PTFE | A | A | |
| FEP | A | A | |
| PVDF | C | C | |
| ECTFE/ETFE | A | B | |
| Elastomers | |||
| EPDM | C | – | |
| Viton (FPM) | D | D | |
| NBR | D | D | |
| Metals | |||
| SS 316 | A* | – | |
| SS 304 | A* | – | |
| Aluminium | A | A | |
* estimated rating, given in the source without a temperature
Not rated in the source, so not in the table: Silicone
Rating scale
- A very good resistance
- B good resistance
- C limited resistance
- D not resistant
- – no data
- K no general statement possible
A rating marked * is an estimate in the source, not a test result. An estimate is given as one value without a temperature.
Frequently Asked Questions
Which materials resist Ethyl Acetate at high concentrations?
The materials with an A rating (resistant) for Ethyl Acetate at 20 °C are: PTFE, HDPE, PP, SS 316, SS 304, Aluminium, FEP, ECTFE/ETFE. These can generally be used in direct contact.
Which materials should be avoided with Ethyl Acetate?
Materials rated D (not resistant) for Ethyl Acetate are: PVC Rigid, Viton (FPM), NBR, Polycarbonate, PVC Flexible, Polystyrene, Polysulfone, PETG. These should not be used in contact with Ethyl Acetate.
Does temperature affect chemical resistance to Ethyl Acetate?
Yes. 4 of 19 tested materials show a worse rating at 50 °C than at 20 °C for Ethyl Acetate. Materials affected include: HDPE, PP, LDPE, ECTFE/ETFE.
Is PTFE safe for Ethyl Acetate?
PTFE is rated A for Ethyl Acetate at 20 °C. A rating of A means resistant, B means limited resistance, C means partly resistant, and D means not resistant.
About this data
The ratings come from the chemical resistance list published by Bürkle GmbH, which compiled them from raw-material manufacturers’ data. They describe laboratory tests on the raw material at 20 °C and 50 °C.
A finished part also sees pressure, mechanical stress, welds and mixtures that a laboratory test does not. Treat the rating as a first filter and test under your own conditions before relying on it.
Chemicals with a similar resistance profile
Same 20 °C rating on the share of materials shown.