ChemicalResistance
ChemicalResistance.org

Ammonium Sulfate Chemical Resistance

Resistance ratings for 24 plastics, elastomers and metals at 20 °C and 50 °C. Listed at 2 concentrations, because the rating depends on it.

At a glance

Based on the row for 10 %, 20 °C.

Rated A, very good resistance
PTFE, HDPE, PP, PVDF, PVC Rigid, EPDM, NBR, SS 316, SS 304, Aluminium, LDPE, FEP, ECTFE/ETFE, Nylon (PA), Acetal (POM), Polycarbonate, Polystyrene, Polysulfone, PMP (19)
Rated B, good resistance
Viton (FPM), PETG (2)
Rated C, limited resistance
none (0)
Rated D, not resistant
none (0)
No data in the source
Silicone, PVC Flexible, SAN
Rated lower at 50 °C than at 20 °C
PVC Rigid (A → C), Viton (FPM) (B → C)
Rating changes with concentration (20 °C)
Acetal (POM): A (10 %), B (saturated)

Based on the row for 10 %, 20 °C.

Rating profile by material family

Ammonium Sulfate: Rating profile by material familyThermoplastics: 10 A, 1 B, 2 no data. Fluoropolymers: 4 A. Elastomers: 2 A, 1 B, 1 no data. Metals: 3 A.Thermoplastics (13)Thermoplastics: 10 × A, very good resistance (HDPE, LDPE, PP, PVC Rigid, PMP, Polystyrene, Polycarbonate, Acetal (POM), Nylon (PA), Polysulfone)A 10Thermoplastics: 1 × B, good resistance (PETG)Thermoplastics: 2 × no data (PVC Flexible, SAN)– 2Fluoropolymers (4)Fluoropolymers: 4 × A, very good resistance (PTFE, FEP, PVDF, ECTFE/ETFE)A 4Elastomers (4)Elastomers: 2 × A, very good resistance (EPDM, NBR)A 2Elastomers: 1 × B, good resistance (Viton (FPM))B 1Elastomers: 1 × no data (Silicone)– 1Metals (3)Metals: 3 × A, very good resistance (SS 316, SS 304, Aluminium)A 3
A very good resistanceB good resistanceC limited resistanceD not resistantno data
Number of materials in each family with each rating at 20 °C.

Effect of temperature, 20 °C to 50 °C

Ammonium Sulfate: Effect of temperature, 20 °C to 50 °CPVC Rigid A → C; Viton (FPM) B → C.ABCDPVC Rigid: A at 20 °C, C at 50 °CPVC RigidViton (FPM): B at 20 °C, C at 50 °CViton (FPM)
20 °C50 °C
Materials whose rating differs between 20 °C and 50 °C. Materials not shown keep their rating or have no 50 °C value.

Substance

CAS number
7783-20-2
Formula
(NH4)2SO4
Hazard symbols in the source
Xn (harmful) (pre-GHS European symbols; check the current safety data sheet)
Concentrations listed
10 %; saturated
Name in the source (German)
Ammoniumsulfat

Rating by concentration

Ammonium Sulfate: Rating by concentrationHDPE: 10 % A, saturated A. LDPE: 10 % A, saturated A. PP: 10 % A, saturated A. PVC Rigid: 10 % A→C, saturated A. PVC Flexible: 10 % –, saturated A. PMP: 10 % A*, saturated A. Polystyrene: 10 % A, saturated A. SAN: 10 % –, saturated A. Polycarbonate: 10 % A, saturated A. PETG: 10 % B*, saturated B*. Acetal (POM): 10 % A, saturated B. Nylon (PA): 10 % A, saturated A. Polysulfone: 10 % A, saturated A. PTFE: 10 % A, saturated A. FEP: 10 % A, saturated A. PVDF: 10 % A, saturated A. ECTFE/ETFE: 10 % A, saturated A. EPDM: 10 % A, saturated A. Viton (FPM): 10 % B→C, saturated B→C. NBR: 10 % A, saturated A. SS 316: 10 % A, saturated A→B. SS 304: 10 % A, saturated A. Aluminium: 10 % A, saturated A.10 %saturatedTHERMOPLASTICSHDPEHDPE, 10 %: A at 20 °C, A at 50 °CAHDPE, saturated: A at 20 °C, A at 50 °CALDPELDPE, 10 %: A at 20 °C, A at 50 °CALDPE, saturated: A at 20 °C, A at 50 °CAPPPP, 10 %: A at 20 °C, A at 50 °CAPP, saturated: A at 20 °C, A at 50 °CAPVC RigidPVC Rigid, 10 %: A at 20 °C, C at 50 °CA→CPVC Rigid, saturated: A at 20 °C, A at 50 °CAPVC FlexiblePVC Flexible, 10 %: no data–PVC Flexible, saturated: A at 20 °CAPMPPMP, 10 %: A at 20 °C (estimate)A*PMP, saturated: A at 20 °C, A at 50 °CAPolystyrenePolystyrene, 10 %: A at 20 °C, A at 50 °CAPolystyrene, saturated: A at 20 °CASANSAN, 10 %: no data–SAN, saturated: A at 20 °C, A at 50 °CAPolycarbonatePolycarbonate, 10 %: A at 20 °C, A at 50 °CAPolycarbonate, saturated: A at 20 °C, A at 50 °CAPETGPETG, 10 %: B at 20 °C (estimate)B*PETG, saturated: B at 20 °C (estimate)B*Acetal (POM)Acetal (POM), 10 %: A at 20 °CAAcetal (POM), saturated: B at 20 °CBNylon (PA)Nylon (PA), 10 %: A at 20 °CANylon (PA), saturated: A at 20 °CAPolysulfonePolysulfone, 10 %: A at 20 °CAPolysulfone, saturated: A at 20 °CAFLUOROPOLYMERSPTFEPTFE, 10 %: A at 20 °C, A at 50 °CAPTFE, saturated: A at 20 °C, A at 50 °CAFEPFEP, 10 %: A at 20 °C, A at 50 °CAFEP, saturated: A at 20 °C, A at 50 °CAPVDFPVDF, 10 %: A at 20 °C, A at 50 °CAPVDF, saturated: A at 20 °C, A at 50 °CAECTFE/ETFEECTFE/ETFE, 10 %: A at 20 °C, A at 50 °CAECTFE/ETFE, saturated: A at 20 °C, A at 50 °CAELASTOMERSEPDMEPDM, 10 %: A at 20 °CAEPDM, saturated: A at 20 °CAViton (FPM)Viton (FPM), 10 %: B at 20 °C, C at 50 °CB→CViton (FPM), saturated: B at 20 °C, C at 50 °CB→CNBRNBR, 10 %: A at 20 °C, A at 50 °CANBR, saturated: A at 20 °C, A at 50 °CAMETALSSS 316SS 316, 10 %: A at 20 °C, A at 50 °CASS 316, saturated: A at 20 °C, B at 50 °CA→BSS 304SS 304, 10 %: A at 20 °C, A at 50 °CASS 304, saturated: A at 20 °C, A at 50 °CAAluminiumAluminium, 10 %: A at 20 °C, A at 50 °CAAluminium, saturated: A at 20 °C, A at 50 °CA
A very good resistanceB good resistanceC limited resistanceD not resistantno data
Each cell shows the rating at 20 °C. Where the rating at 50 °C differs, it follows the arrow. * marks an estimate in the source.
Show as a table
Material10 %saturated
Thermoplastics
HDPEAA
LDPEAA
PPAA
PVC RigidAA
PVC Flexible–A
PMPA*A
PolystyreneAA
SAN–A
PolycarbonateAA
PETGB*B*
Acetal (POM)AB
Nylon (PA)AA
PolysulfoneAA
Fluoropolymers
PTFEAA
FEPAA
PVDFAA
ECTFE/ETFEAA
Elastomers
EPDMAA
Viton (FPM)BB
NBRAA
Silicone––
Metals
SS 316AA
SS 304AA
AluminiumAA

* estimated rating, given in the source without a temperature

Resistance table: Ammonium Sulfate, 10 %

Remark: schwefelsaures Ammoniak

Material20 °C50 °CRemark
Thermoplastics
HDPEAA
LDPEAA
PPAA
PVC RigidAC
PMPA*–
PolystyreneAA
PolycarbonateAA
PETGB*–
Acetal (POM)A–
Nylon (PA)A–
PolysulfoneA–
Fluoropolymers
PTFEAA
FEPAA
PVDFAA
ECTFE/ETFEAA
Elastomers
EPDMA–
Viton (FPM)BC
NBRAA
Metals
SS 316AA
SS 304AA
AluminiumAA

* estimated rating, given in the source without a temperature

Not rated in the source, so not in the table: PVC Flexible, SAN, Silicone

Resistance table: Ammonium Sulfate, saturated

Remark: schwefelsaures Ammoniak

Material20 °C50 °CRemark
Thermoplastics
HDPEAA
LDPEAA
PPAA
PVC RigidAA
PVC FlexibleA–
PMPAA
PolystyreneA–
SANAA
PolycarbonateAA
PETGB*–
Acetal (POM)B–
Nylon (PA)A–
PolysulfoneA–
Fluoropolymers
PTFEAA
FEPAA
PVDFAA
ECTFE/ETFEAA
Elastomers
EPDMA–
Viton (FPM)BC
NBRAA
Metals
SS 316AB
SS 304AA
AluminiumAA

* estimated rating, given in the source without a temperature

Not rated in the source, so not in the table: Silicone

Rating scale

A rating marked * is an estimate in the source, not a test result. An estimate is given as one value without a temperature.

Frequently Asked Questions

Which materials resist Ammonium Sulfate at high concentrations?

The materials with an A rating (resistant) for Ammonium Sulfate at 20 °C are: PTFE, HDPE, PP, PVDF, PVC Rigid, EPDM, NBR, SS 316. These can generally be used in direct contact.

Does temperature affect chemical resistance to Ammonium Sulfate?

Yes. 2 of 15 tested materials show a worse rating at 50 °C than at 20 °C for Ammonium Sulfate. Materials affected include: PVC Rigid, Viton (FPM).

Is PTFE safe for Ammonium Sulfate?

PTFE is rated A for Ammonium Sulfate at 20 °C. A rating of A means resistant, B means limited resistance, C means partly resistant, and D means not resistant.

Does concentration affect chemical resistance to Ammonium Sulfate?

Yes. Ammonium Sulfate is tested at 2 concentrations (10 %, saturated). Some materials change their rating depending on the concentration.

About this data

The ratings come from the chemical resistance list published by Bürkle GmbH, which compiled them from raw-material manufacturers’ data. They describe laboratory tests on the raw material at 20 °C and 50 °C.

A finished part also sees pressure, mechanical stress, welds and mixtures that a laboratory test does not. Treat the rating as a first filter and test under your own conditions before relying on it.

Chemicals with a similar resistance profile

Same 20 °C rating on the share of materials shown.

Ammonium Nitrate 95 %Aluminum Oxide 90 %Calcium Carbonate 90 %Calcium Sulfate 90 %Distilled Water 90 %Gelatin 90 %